Showing posts with label C. Show all posts
Showing posts with label C. Show all posts

Tuesday, June 11, 2013

Fuel Clunk

A weighted fuel pick-up used in a fuel tank to assure the intake line is always in fuel.

Clunk

The Nitro Fuel Tank Clunk
For those of you in the RC airplane world this is nothing new, but it might be a new term or idea for those of you with nitro RC cars, truck, or boats.

RC aircraft fly in many different attitudes – meaning pointing up, pointing down, on their sides, and upside down... not to mention the high G forces pulling the fuel to one side of the tank or the other.

If the fuel pick up was at a fixed location in the tank – say the lowest part of the tank like in a car – the air craft would only get fuel when it is flying straight and level. Any banking or inverted flying would starve the engine of nitro fuel.

A very simple solution of using a short length of fuel tubing inside the fuel tank with a heavy weight at the end of the tube called a "CLUNK" ensures no fuel starvation. This tube and clunk will simply flop around inside the fuel tank which ever way gravity pulls on it - just like the fuel in the tank. This means no mater what the RC aircraft is doing, the pick up end of the fuel tube in the tank is always submerged in fuel.

This clunk, more specifically the fuel tube it is hooked up to inside the fuel tank should be checked for deterioration every year or so. The tube over the years will get brittle and may crack or come off the supply tube in your fuel tank. This of course means you now have a fixed nitro fuel pick-up and all the benefits of the clunk are lost.

Posted on Tuesday, June 11, 2013 by Admin OG

No comments

Chicken Stick, Airplane Engine Start

A hand-held stick used to "flip start" a model airplane engine.

The Hobbico Safe Start "chicken stick" is a safe, easy way to Flip-Start Glow Powered Engines. This stick is held in your hand and with the extended end placed against the propeller on the engine. Then with a quick flip of the wrist to rotate the prop, starting the engine.
Start-R-Stik Standard Large by Davis Diesel Development



Posted on Tuesday, June 11, 2013 by Admin OG

No comments

Tuesday, June 4, 2013

Charger Tips
CHARGER TIPS:


  1. Your always there to monitor the cells (don't leave it unattended) 
  2. Get a quailty battery (Thunder Powers are great) 
  3. Quailty LIPO CHARGER, you MUST (notice the caps) get a LIPO CHARGER. You cannot charge lipos with ordinary chargers for NI-CD, etc.
  4. Investing in a good balancer is a wise decision 
  5. Get well known Lipo batteries. DO NOT get no named cheap batteries just because their cheap because you might have to spend another $10,000 fixing your house if it burns.
  6. It is not mandatory for you to get a fire-proof box but it is recommended
  7. Do not charge/store your lipo on your plane/heli
  8. Do not charge near flammables/explosive substances (common sense)
  9. If your pack is damaged/broken, soak it in salt water for a while then contact your hazardous waste disposal company for advice on throwing it out
  10. DO NOT OVERDISCHARGE YOUR LI-PO BATTERY (don't fly until you can't get the rotor to turn anymore)!!!
  11. Store in a dry, cool area with some sort of case (so it won't get damaged)
  12. Connect your charger to the main power supply first then your battery to your charger to prevent shorting your pack
  13. Double, Triple check your setting on your charger before you charge your battery
  14. Read the charger manual before you charge
  15. Always solder the female plug onto the battery.
  16. If any single cell in your lipo drops below 3.0 volts your pack may be ruined. 9.0 volts for a 3 cell pack is too low of a setting on a monitor.
  17. IF you crash, set your lipo aside in a safe place for a while, even if it looks undamaged. Internal shorting can occure and cause a fire
  18. When setting up a lipo power system, always try to match battery Mah capacity to be at least, over the expected current draw from your motor and ESC systems. Always use good quality power connectors like deans or similar. Poor quality connectors can = meltdown = burnt model = burnt house or car = dead modeller.
  19. Li-pos should NOT get warm during a charge. During a discharge, they should not exceed 140F (worst case, lower is obviously better). 


 Be Bright, Charge Right
 Charge Wrong, Your Gone

Posted on Tuesday, June 04, 2013 by Admin OG

1 comment

Li po battery charger

Device used to recharge batteries, usually supplied with the radio if NiCd batteries are included.
Digital charger
LiPo charger: It is imperative that you use a specially made LiPo charger to recharge your batteries. Never use a charger designed for other types of rechargeable battery, the charging current will be wrong and there is no safety switch-off, the need to stop all LiPo chargers overcharging. Overcharging a LiPo battery, the battery caught fire, there are reports of exploding batteries.

Charge Rate: Always make sure that your charger at the same voltage as your LiPo battery. LiPo batteries are commonly used in batteries, so many chargers have a variable fee setting so that you can charge more packs. Check the label on the battery or battery to determine the output voltage. Place the charger on the same voltage, a little lower no problem, but a higher voltage damages the battery and can be dangerous, as in Section 1.

Excessive Discharge: LiPo batteries can be recharged at any point during the discharge with no ill effects or damage. However, if you fully discharge the battery and try to successfully - and that's unlikely, since LiPo manufacturers have built in a safety device to prevent this - it will not recharge. This is because, deep discharge destroys the chemical basis of the battery and make it unusable.

LiPo Charging: BagLegen Always store your batteries in a bag while they are chargeable. The bag is a fire and explosion protection so that if a problem occurs while the batteries are charged, you will be safe. They are fairly inexpensive and widely available from electrical and hobby stores. Never leave LiPo batteries, the charge will be unsupervised. Always turn the charger when the batteries are charged and allow them in the bag before they cool.


CHARGER TIPS

Posted on Tuesday, June 04, 2013 by Admin OG

No comments

Monday, May 20, 2013

Charge Jack
Charge Jack: The plug receptacle of the switch harness into which the charger is plugged to charge the airborne battery. An expanded scale voltmeter (ESV) can also be plugged into it to check battery voltage between flights. It is advisable to mount the charge jack in an accessible area of the fuselage so an ESV can be used without removing the wing.

Charge Jack Plug

Posted on Monday, May 20, 2013 by Admin OG

No comments

CG (Center of Gravity)
CG ("Center of Gravity"): For modeling purposes, this is usually considered -- the point at which the airplane balances fore to aft. This point is critical in regards to how the airplane reacts in the air. A tail-heavy plane will be very snappy but generally very unstable and susceptible to more frequent stalls. If the airplane is nose heavy, it will tend to track better and be less sensitive to control inputs, but, will generally drop its nose when the throttle is reduced to idle. This makes the plane more difficult to land since it takes more effort to hold the nose up. A nose heavy airplane will have to come in faster to land safely.

Posted on Monday, May 20, 2013 by Admin OG

No comments

Rc Engine Carburetor
The part of the engine which controls the speed or throttle setting and lean/rich mixture via setting of the needle valve.

A carburetor (American and Canadian spelling), carburator, carburettor, or carburetter (Commonwealth spelling) is a device that blends air and fuel for an internal combustion engine. It is sometimes, but not always, shortened to carb in North America and the United Kingdom.

Slide Carburetors
A slide carburetor has a throttle valve that slides out the side. This reduces air restriction, for better performance, and requires the servo to move less to open it fully, for better throttle response. They also require a more precise alignment of the carburetor and throttle servo to prevent binding, which can result in dangerous stuck throttle conditions, which can often only be resolved by killing the engine after the vehicle is stopped by a large immobile object like a tree. Slide carbs are used on all big block nitro engines, and on many small block nitro engines. They are fairly prone to sticking because of dirt, and on land vehicles, an air filter is always used.

Rotary Carburetors
Rotary carburetors have a barrel with a hole in it that rotates. This takes more servo movement to completely open, and reduces throttle resopnse. They also have more restriction, which can reduce overall power. Some people feel that these are better for offroad use, because they have more throttle range. They aren't used on big block engines. They are as prone to dirt as a slide carb.

Butterfly Carburetors
Butterfly carburetors are common on gasoline RC engines and small 2 stroke engines designed for other purposes but used on RCs. They have a butterfly, or a thin piece of metal that rotates to open the throttle. They don't stick when they get dirty, but the dirt can still cause engine damage and poor performance. These carburetors are also used in alot of full scale applications, like cars and lawnmowers. They often have a second butterfly as a choke valve, to reduce air flow, temporarily richening the mixture for easier starting. These carburetors have more restriction then other carburetors, but the engines they are used on are larger, and the performance doesn't matter as much.

Nitro Rc Engine Diagram
Nitro Rc Engine Diagram
  • Cylinder Head
  • Glow Plug
  • Pullstart
  • Combustion Chamber
  • Piston
  • Exhaust port
  • Carburetor
  • Mixture needle
  • Idle screw
  • Throttle linkage
  • Crankcase
  • Crankshaft

Posted on Monday, May 20, 2013 by Admin OG

No comments

Friday, May 10, 2013

CA, Cyanoacrylate
CA :
(Abbreviation for "Cyanoacrylate") - An instant type glue that is available in various viscosities (Thin, Medium, Thick, and Gel). These glues are ideal for the assembly of wood airplanes and other materials. Note: Most CA glues will attack Styrofoam.

Posted on Friday, May 10, 2013 by Admin OG

No comments